USB Multilink Universal FX高速仿真器U-multilink-FX

　　USB Multilink Universal FX仿真器U-MULTLINK FX

　　P&E’sUSB Multilink Universal FXis ahigh-speed, all-in-one development interface which allows a PC access to the Background Debug Mode (BDM) or JTAG interface on many different Freescale MCU architectures (see plete list below). The FX's high-speed USB interface allows munications between your Windows machine and the standard debug connector on the target. The Freescale microcontrollers are supported via the multiple headers located on the USB Multilink Universal FX. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included.

　　· Can provide power to the target MCU

　　· I/O line clamping for added protection

　　· Supports additional Freescale devices

　　*The exceptional performance increases seen with the USB Multilink Universal FX are limited to synchronous architectures:Kinetis, Qorivva, Coldfire V2-V4, Power Architecture PX Series, DSC, and HC16/683xx.

　　By using theUSB Multilink Universal FX, the user can take advantage of the background debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices. The USB Multilink Universal FX can also provide power to your target MCU, either 3.3V or 5V.

　　TheUSB Multilink Universal FXis natively supported by recent versions of CodeWarrior®, current P&E software applications, and toolchains from many Freescale partners including IAR, Keil, Cosmic, and Green Hills (check with the vendor for device patibility). A list of supported software can be foundhere.

　　For many of the supported processors, P&E has a set of interface libraries allowing the user to write their own Windows-based application which interacts with P&E's debug interface.

　　This interface is USB 2.0 patible, and it is also backwards patible with USB 1.1 ports.

　　NOTE: For production usage, see either theCyclone PROorCyclone MAXstand alone programmer and debug interface, depending on which processor you are working with. Aparison chartis available below to help you choose the appropriate interface.

　　FEATURES:

　　· High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and patibility of the USB interface.

　　· Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).

　　· Can be used to power target MCU.

　　· Target Voltage: 1.6V-5.25V

　　· Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)

　　· I/O line clamping for added protection

　　· Auto-frequency detection + trimming capabilities for HCS08 devices.

　　· Auto-frequency detection for HC(S)12(X) devices.

　　· Generates programming voltage on RESET line for RS08 devices.

　　Includes:

　　· One (1) USB 2.0 High Speed Cable, Type A to Type B, 6-ft.

　　· One (1) 6-pin 0.100" pitch ribbon cable for connecting to RS08, HCS08, HC(S)12(X), S12Z, ColdFire V1/V1+ targets

　　· One (1) 10-pin 0.100" pitch ribbon cable for connecting to HC16/683xx targets

　　· One (1) 14-pin 0.100" pitch ribbon cable for connecting to QorivvaMPC5xxx, Power ArchitecturePX Series,DSCtargets

　　· One (1) 26-pin 0.100" pitch ribbon cable for connecting to asynchronous ColdFire V2/V3/V4 targets

　　· One (1) 20-pin 0.100" pitch ribbon cable for connecting to Kinetis targets

　　· One (1) 20-pin 0.050" pitch ribbon cable for connecting to Kinetis targets