Atmel STK600 ATSTK600开发套件 编程器

　　Atmel STK600 (ATSTK600)

　　Select your routing card and socket card by using the Store Search and select device

　　The STK600 is a plete starter kit and development system for the R flash microcontrollers from ATMEL® Corporation. It is designed to give designers a quick start to develop code on the R, bined with advanced features for using the starter kit to prototype and test new designs.

　　§ R Studio 4/R32 Studio patible

　　§ USB Interface to PC for programming and control

　　§ Powered from USB bus or from an external 10-15V DC power supply

　　§ Adjustable target VCC (0-5.5V)

　　§ Two adjustable reference voltages with high accuracy. (0-5.0V, 10mV res)

　　§ Clock oscillator, adjustable on the fly from RStudio (0-50MHz, 0.1% res)

　　§ Serial In-System Programming (ISP) of tinyR and megaR devices

　　§ PDI Programming of XMEGA devices

　　§ JTAG programming of 8-bit megaR, 8/16-bit R XMEGA and 32-bit R UC3 devices

　　§ aWire Programming of 32-bit R UC3 devices

　　§ ISP and JTAG programming of R devices in external target systems

　　§ Flexible routing and socket card system for easy mounting of all supported devices

　　§ 8 push-buttons for general use

　　§ 8 LEDs for general use

　　§ All R I/O ports easily accessible through pin header connectors

　　§ Expansion connectors for plug-in modules and prototyping area

　　§ On-board 2Mbit Dataflash for non-volatile data

　　§ USB mini-AB (On-The-Go) connector for R devices with USB

　　§ PHY and DSUB-9 connetor for RS232 interface

　　§ PHY and DSUB-9 connector for CAN bus

　　§ PHY and header for LIN bus

　　§ Device board with an ATmega2560 R microcontroller is included.

　　The STK600 supports the whole range of R microcontrollers, from the smallest 6-pin 8-bit tinyR up to the large 144-pin 32-bit R UC3 devices.

　　The R device is connected to the STK600 using an innovative routing and socketcard sandwich system, which routes the signals from the device to the appropriate hardware.

　　The system consists of a generic socketcard, on which the R device is inserted, and a device specific signal routing card, which routes the signals from the socket pins to the different functions on the STK600 main board dependant on the device.

　　The system simplifies the hardware setup when switching from one R device to another, since all connections from the device to the motherboard is determined by the routingcard, which is a custom board for each device. The routing system is purely passive, i.e. no electronic ponents are used to route the signals, and hence all I/O pins are directly accessible on the connectors with no altering of the electrical behavior.

　　With access to all device pins, and several useful hardware functions that can be connected, such as pushbuttons, LEDs, dataflash, etc, the kit provides a plete system to prototype and test new designs.

　　With the free R Studio the user can write and pile firmware in either assembly or C language, and download the code to the target R device.

　　The board also has adjustable voltage supply and adjustable clock to the target R device. The VCC level and clock frequency can be adjusted on the fly from R Studio, and gives the designer the ability to test the performance at different voltage levels and clock frequencies with just the click of a button.

　　李 进

　　深圳博瑞图电子科技有限公司

　　TEL :

　　MOB :

　　FAX :

　　ADD :深圳市福田区福中航路都会轩1416

　　EMAIL :lijin810230@163.COM

　　网 址：